• Z945X Motor Operated Gate Valve
  • Z945X Motor Operated Gate Valve
  • Z945X Motor Operated Gate Valve
  • Z945X Motor Operated Gate Valve
  • Z945X Motor Operated Gate Valve
  • Z945X Motor Operated Gate Valve
Z945X Motor Operated Gate Valve
Z945X Motor Operated Gate Valve
Z945X Motor Operated Gate Valve
Z945X Motor Operated Gate Valve
Z945X Motor Operated Gate Valve
Z945X Motor Operated Gate Valve
+

Z945X Motor Operated Gate Valve

Motor operated soft seal gate valve Z945X with LCD actuator, selector knob and handwheel emergency override. DN40-DN1200, PN16-PN25, QT450 body, flanged.

Contact HENGYA for Shipping, delivery, and payments information.

Tag list

  • 产品描述
  • Design features

    • Resilient seated gate valve with a multi-turn electric actuator mounted directly on the yoke - no pedestal or linkage to align
    • Non-rising stem keeps the overall height low, so the valve suits pits and plant rooms with limited headroom
    • Rubber encapsulated disc gives bubble-tight shut-off on water and general industrial media
    • Handwheel on the actuator for manual operation when power is off or during commissioning
    • Selector knob for local, stop and remote operation, with a visible LCD window showing valve position
    • Flange ends to EN 1092-2, so it drops into a standard flanged pipe run
    • Lifting eye on the yoke for safe handling of the larger sizes

    The actuator

    The multi-turn actuator sits on the valve yoke and drives the stem through a gear train. What is visible on the housing is what the operator works with day to day:

    • LCD window - shows valve position and operating status without opening anything
    • Selector knob - switches between local control, stop and remote control
    • Setting knob - for configuration at commissioning
    • Handwheel - manual operation for power failure, commissioning and emergency closing

    The motor housing is at the end of the actuator barrel. Electrical connection is made through the two cable entries on top of the housing, so the supply and the control signal can be run in separate glands.

    How it works

    The gate is a wedge faced with rubber, guided in the body and moved up and down by the stem. Turning the stem lifts the gate clear of the seat to open the bore, and drives it back down to close. Because the gate travels the full bore height, the valve is used for isolation rather than throttling - it is either fully open or fully closed.

    In electric operation the actuator motor turns the stem through the gear train until the limit set for the open or closed position is reached, then cuts out. The LCD shows where the valve is. If the supply fails, the handwheel takes over on the same stem.

    Technical specification

    ModelZ945X
    Nominal sizeDN40 - DN1200
    Nominal pressurePN16 / PN25
    Body materialDuctile iron QT450-10
    DiscDuctile iron with EPDM rubber encapsulation
    StemNon-rising
    Working mediumWater and general industrial media
    Working temperature0 - 80 °C
    ConnectionFlanged, ISO 7005 / EN 1092-2
    OperationMulti-turn electric actuator, handwheel override
    Pressure testShell 1.5 x PN, seal 1.1 x PN to EN 12266-1

    Pressure ratings

    ParameterPN16PN25
    Nominal pressure (MPa)1.62.5
    Shell test pressure (MPa)2.43.75
    Seal test pressure (MPa)1.762.75

    Materials of construction

    Body / BonnetDuctile iron QT450-10, epoxy coated inside and out
    DiscDuctile iron core, EPDM rubber encapsulated
    StemStainless steel
    Stem nutBrass
    Gland / O-ringsEPDM
    Actuator housingDie-cast aluminium, epoxy coated
    FastenersStainless steel

    Dimensions

    Face-to-face length, flange drilling, overall height and actuator clearance for each size follow the drawing supplied with the quotation. Flange dimensions meet EN 1092-2 for the pressure rating ordered. Allow headroom above the actuator for the handwheel and for lifting the unit on installation.

    Installation

    • Fits horizontal or vertical pipe; on vertical runs prefer flow upwards
    • Follow the flow-direction arrow cast on the body
    • Support the pipe either side on large sizes - the actuator adds weight at the top of the valve
    • No pipeline stress may act on the body after bolting up
    • Leave access to the actuator for setting and for manual operation
    • Flush the line before commissioning so debris does not lodge in the seat pocket
    • Wire the supply and control signal through separate cable entries and check the direction of rotation before coupling to the valve

    Operating modes and manual override

    The selector knob has three positions:

    1. Local - open and close from the actuator itself, used during commissioning and testing
    2. Stop - the actuator holds position and ignores commands, used while work is done downstream
    3. Remote - the actuator follows the control signal from the plant system

    For manual operation, engage the handwheel and turn it until the valve reaches the required position; the LCD shows the travel. Return the selector to its working position and disengage the handwheel before restoring electric operation, so the motor does not fight the manual drive.

    Standards and certification

    Flange dimensionsISO 7005 / EN 1092-2
    Pressure testingEN 12266-1
    Quality managementISO 9001, certificate no. 05325Q30683R1S
    Environmental managementISO 14001, certificate no. 05325E30489R1S
    Occupational health and safetyISO 45001, certificate no. 05325S30455R1S

    ISO 9001, ISO 14001 and ISO 45001 certificates are held by Hebei Hengya Technology Co., Ltd. and are valid until 19 October 2028.

    Applications

    • Pump station discharge and suction isolation, opened and closed from the control room
    • Water treatment plants, where valves sit in pits and are operated remotely
    • District metering and transmission mains, for section isolation
    • HVAC plant rooms and boiler houses, on circulating water headers
    • Industrial water supply lines and cooling water circuits
    • Buried and semi-buried installations where a manual valve would be inaccessible

Z945X Motor Operated Gate Valve

Motor operated soft seal gate valve Z945X with LCD actuator, selector knob and handwheel emergency override. DN40-DN1200, PN16-PN25, QT450 body, flanged.

Contact HENGYA for Shipping, delivery, and payments information.

Share to

Tag list

Send Inquiry

*Note: Please fill in the information accurately and keep the communication open. We will contact you as soon as possible.

Submit

Related Products

BS5163 non-rising stem soft seal gate valve, Z45X, ductile iron body with epoxy coating and EPDM seat. DN40-DN1200, PN10-PN25, flanged to EN 1092-2.
View Details View More
BS5163 rising stem soft seal gate valve, Z41X, stem position showing disc travel, ductile iron body. DN40-DN1200, PN10-PN25, flanged.
View Details View More
BS5163 Z45X heavy duty soft seal gate valve, thicker body wall for high pressure mains. DN40-DN1200, PN16-PN25, flanged, non-rising stem.
View Details View More
CFZ45X magnetic lock soft seal gate valve, key operated locking head against unauthorised use. DN40-DN300, PN10-PN16, flanged.
View Details View More
< 1234...16 >

Request Quote

We will contact you within one working day. Please pay attention to your email.

SUBMIT