• 200X Pilot Operated Pressure Reducing Valve
  • 200X Pilot Operated Pressure Reducing Valve
  • 200X Pilot Operated Pressure Reducing Valve
  • 200X Pilot Operated Pressure Reducing Valve
200X Pilot Operated Pressure Reducing Valve
200X Pilot Operated Pressure Reducing Valve
200X Pilot Operated Pressure Reducing Valve
200X Pilot Operated Pressure Reducing Valve
+

200X Pilot Operated Pressure Reducing Valve

Design featuresPilot-operated, self-powered: the line pressure itself drives the main disc, so no external power supply is neededFull-bore streamlined flow path, low fluid resistance and high flow capacityDownstream pressure held at the value set by the pilot valve spring; the valve closes automatically when outlet pressure exceeds the settingStainless steel pilot head with adjusting screw and locknut, plus inlet and outlet pressure gauges for setting and checkingBrass strainer in the pilot circuit protects the needle valve and pilot valve from pipeline debrisDiaphragm separates the control chamber from the line medium, keeping the pilot circuit cleanHow it worksThe 200X is a hydraulically operated control valve made up of a main valve and an auxiliary pilot control system: pilot piping, a needle valve, a ball valve, a pilot valve and two pressure gauges. Water pressure in the pipeline moves the main valve disc up and down, changing the opening of the valve port and regulating the downstream pressure. The pilot circuit sets the pressure acting on the diaphragm, which positions the main disc. When downstream pressure reaches the set value, the valve throttles and holds outlet pressure constant.Technical specificationModel200XNominal sizeDN50 - DN600Nominal pressurePN10 / PN16 / PN25Body materialDuctile iron QT450-10Working mediumWaterWorking temperature0 - 80 °CConnectionFlanged, ISO 7005 / EN 1092-2 (PN10 / PN16 / PN25)Pressure testShell 1.5 x PN, seal 1.1 x PN to EN 12266-1Pressure ratings and adjustable outlet rangeParameterPN10PN16PN25Nominal pressure (MPa)1.01.62.5Shell test pressure (MPa)1.52.43.75Seal test pressure (MPa)1.11.762.75Maximum inlet pressure (MPa)1.01.62.5Outlet pressure adjustable range (MPa)0.09 - 0.80.10 - 1.20.15 - 1.6Outlet pressure is set at the pilot valve to the ordered value before dispatch. The DN100 unit shown in the photographs is set to 0.75 MPa; the adjustable range for each pressure rating is given in the table above.Materials of constructionBody / BonnetDuctile iron QT450-10Disc / Clamp plateDuctile iron QT450-10Stem20Cr13 martensitic stainless steel (AISI 420)SeatDN50 - DN200: stainless steel 304; DN250 - DN600: brassDiaphragm / GasketEPDMSpringStainless steel 304Pilot valve / Needle valve / Ball valve / Elbow / StrainerBrassBottom plateCarbon steelHex bolt / NutStainless steel 201Dimensions (mm)DNLD2D1n - dia.TFD502151651254-1919399652351851454-19193118802752001608-191931321003062201808-191931561253062502108-191931841503752852408-231932112004303402958-23 / 12-23203266L face-to-face, D2 outside diameter of flange, D1 bolt circle diameter, n-dia. number and diameter of bolt holes, T flange thickness, F raised face height, D overall height. DN250 and above to drawing.InstallationInstall horizontally with the bonnet facing upwards; other orientations also workClean all debris out of the pipeline before fittingFollow the flow-direction arrow on the bodyNo pipeline stress may act on the body or its internals after installationFit a gate valve and a strainer upstream, and a gate valve downstream, so the valve can be servicedFlush the system thoroughly before admitting water; fit a bypass on important supply linesSetting the outlet pressureClose the upstream isolating valve, open the downstream valve to release pressure, wait until it falls to zero, then close itTurn the pilot adjusting screw to its uppermost position and open the needle valve about half a turnOpen the upstream isolating valve slowly and fullyScrew the pilot adjusting screw down gradually; outlet pressure rises. Lock the screw when the required set point is reachedAdjust in small increments while watching the downstream gauge. Pressure can only be set upwards from a lower value - if set too high, repeat from step 1Standards and certificationFlange dimensionsISO 7005 / EN 1092-2Pressure testingEN 12266-1Quality managementISO 9001, certificate no. 05325Q30683R1SEnvironmental managementISO 14001, certificate no. 05325E30489R1SOccupational health and safetyISO 45001, certificate no. 05325S30455R1SISO 9001, ISO 14001 and ISO 45001 certificates are held by Hebei Hengya Technology Co., Ltd. and are valid until 19 October 2028.ApplicationsWater supply networks where a high-pressure main feeds a lower-pressure distribution zoneBuilding installations requiring a stable reduced pressureFire-fighting water supply systemsIndustrial water supply and process lines

Contact HENGYA for Shipping, delivery, and payments information.

Products Category

Tag list

  • 产品描述
  • Design features

    • Pilot-operated, self-powered: the line pressure itself drives the main disc, so no external power supply is needed
    • Full-bore streamlined flow path, low fluid resistance and high flow capacity
    • Downstream pressure held at the value set by the pilot valve spring; the valve closes automatically when outlet pressure exceeds the setting
    • Stainless steel pilot head with adjusting screw and locknut, plus inlet and outlet pressure gauges for setting and checking
    • Brass strainer in the pilot circuit protects the needle valve and pilot valve from pipeline debris
    • Diaphragm separates the control chamber from the line medium, keeping the pilot circuit clean

    How it works

    The 200X is a hydraulically operated control valve made up of a main valve and an auxiliary pilot control system: pilot piping, a needle valve, a ball valve, a pilot valve and two pressure gauges. Water pressure in the pipeline moves the main valve disc up and down, changing the opening of the valve port and regulating the downstream pressure. The pilot circuit sets the pressure acting on the diaphragm, which positions the main disc. When downstream pressure reaches the set value, the valve throttles and holds outlet pressure constant.

    Technical specification

    Model200X
    Nominal sizeDN50 - DN600
    Nominal pressurePN10 / PN16 / PN25
    Body materialDuctile iron QT450-10
    Working mediumWater
    Working temperature0 - 80 °C
    ConnectionFlanged, ISO 7005 / EN 1092-2 (PN10 / PN16 / PN25)
    Pressure testShell 1.5 x PN, seal 1.1 x PN to EN 12266-1

    Pressure ratings and adjustable outlet range

    ParameterPN10PN16PN25
    Nominal pressure (MPa)1.01.62.5
    Shell test pressure (MPa)1.52.43.75
    Seal test pressure (MPa)1.11.762.75
    Maximum inlet pressure (MPa)1.01.62.5
    Outlet pressure adjustable range (MPa)0.09 - 0.80.10 - 1.20.15 - 1.6

    Outlet pressure is set at the pilot valve to the ordered value before dispatch. The DN100 unit shown in the photographs is set to 0.75 MPa; the adjustable range for each pressure rating is given in the table above.

    Materials of construction

    Body / BonnetDuctile iron QT450-10
    Disc / Clamp plateDuctile iron QT450-10
    Stem20Cr13 martensitic stainless steel (AISI 420)
    SeatDN50 - DN200: stainless steel 304; DN250 - DN600: brass
    Diaphragm / GasketEPDM
    SpringStainless steel 304
    Pilot valve / Needle valve / Ball valve / Elbow / StrainerBrass
    Bottom plateCarbon steel
    Hex bolt / NutStainless steel 201

    Dimensions (mm)

    DNLD2D1n - dia.TFD
    502151651254-1919399
    652351851454-19193118
    802752001608-19193132
    1003062201808-19193156
    1253062502108-19193184
    1503752852408-23193211
    2004303402958-23 / 12-23203266

    L face-to-face, D2 outside diameter of flange, D1 bolt circle diameter, n-dia. number and diameter of bolt holes, T flange thickness, F raised face height, D overall height. DN250 and above to drawing.

    Installation

    • Install horizontally with the bonnet facing upwards; other orientations also work
    • Clean all debris out of the pipeline before fitting
    • Follow the flow-direction arrow on the body
    • No pipeline stress may act on the body or its internals after installation
    • Fit a gate valve and a strainer upstream, and a gate valve downstream, so the valve can be serviced
    • Flush the system thoroughly before admitting water; fit a bypass on important supply lines

    Setting the outlet pressure

    1. Close the upstream isolating valve, open the downstream valve to release pressure, wait until it falls to zero, then close it
    2. Turn the pilot adjusting screw to its uppermost position and open the needle valve about half a turn
    3. Open the upstream isolating valve slowly and fully
    4. Screw the pilot adjusting screw down gradually; outlet pressure rises. Lock the screw when the required set point is reached
    5. Adjust in small increments while watching the downstream gauge. Pressure can only be set upwards from a lower value - if set too high, repeat from step 1

    Standards and certification

    Flange dimensionsISO 7005 / EN 1092-2
    Pressure testingEN 12266-1
    Quality managementISO 9001, certificate no. 05325Q30683R1S
    Environmental managementISO 14001, certificate no. 05325E30489R1S
    Occupational health and safetyISO 45001, certificate no. 05325S30455R1S

    ISO 9001, ISO 14001 and ISO 45001 certificates are held by Hebei Hengya Technology Co., Ltd. and are valid until 19 October 2028.

    Applications

    • Water supply networks where a high-pressure main feeds a lower-pressure distribution zone
    • Building installations requiring a stable reduced pressure
    • Fire-fighting water supply systems
    • Industrial water supply and process lines

200X Pilot Operated Pressure Reducing Valve

Design featuresPilot-operated, self-powered: the line pressure itself drives the main disc, so no external power supply is neededFull-bore streamlined flow path, low fluid resistance and high flow capacityDownstream pressure held at the value set by the pilot valve spring; the valve closes automatically when outlet pressure exceeds the settingStainless steel pilot head with adjusting screw and locknut, plus inlet and outlet pressure gauges for setting and checkingBrass strainer in the pilot circuit protects the needle valve and pilot valve from pipeline debrisDiaphragm separates the control chamber from the line medium, keeping the pilot circuit cleanHow it worksThe 200X is a hydraulically operated control valve made up of a main valve and an auxiliary pilot control system: pilot piping, a needle valve, a ball valve, a pilot valve and two pressure gauges. Water pressure in the pipeline moves the main valve disc up and down, changing the opening of the valve port and regulating the downstream pressure. The pilot circuit sets the pressure acting on the diaphragm, which positions the main disc. When downstream pressure reaches the set value, the valve throttles and holds outlet pressure constant.Technical specificationModel200XNominal sizeDN50 - DN600Nominal pressurePN10 / PN16 / PN25Body materialDuctile iron QT450-10Working mediumWaterWorking temperature0 - 80 °CConnectionFlanged, ISO 7005 / EN 1092-2 (PN10 / PN16 / PN25)Pressure testShell 1.5 x PN, seal 1.1 x PN to EN 12266-1Pressure ratings and adjustable outlet rangeParameterPN10PN16PN25Nominal pressure (MPa)1.01.62.5Shell test pressure (MPa)1.52.43.75Seal test pressure (MPa)1.11.762.75Maximum inlet pressure (MPa)1.01.62.5Outlet pressure adjustable range (MPa)0.09 - 0.80.10 - 1.20.15 - 1.6Outlet pressure is set at the pilot valve to the ordered value before dispatch. The DN100 unit shown in the photographs is set to 0.75 MPa; the adjustable range for each pressure rating is given in the table above.Materials of constructionBody / BonnetDuctile iron QT450-10Disc / Clamp plateDuctile iron QT450-10Stem20Cr13 martensitic stainless steel (AISI 420)SeatDN50 - DN200: stainless steel 304; DN250 - DN600: brassDiaphragm / GasketEPDMSpringStainless steel 304Pilot valve / Needle valve / Ball valve / Elbow / StrainerBrassBottom plateCarbon steelHex bolt / NutStainless steel 201Dimensions (mm)DNLD2D1n - dia.TFD502151651254-1919399652351851454-19193118802752001608-191931321003062201808-191931561253062502108-191931841503752852408-231932112004303402958-23 / 12-23203266L face-to-face, D2 outside diameter of flange, D1 bolt circle diameter, n-dia. number and diameter of bolt holes, T flange thickness, F raised face height, D overall height. DN250 and above to drawing.InstallationInstall horizontally with the bonnet facing upwards; other orientations also workClean all debris out of the pipeline before fittingFollow the flow-direction arrow on the bodyNo pipeline stress may act on the body or its internals after installationFit a gate valve and a strainer upstream, and a gate valve downstream, so the valve can be servicedFlush the system thoroughly before admitting water; fit a bypass on important supply linesSetting the outlet pressureClose the upstream isolating valve, open the downstream valve to release pressure, wait until it falls to zero, then close itTurn the pilot adjusting screw to its uppermost position and open the needle valve about half a turnOpen the upstream isolating valve slowly and fullyScrew the pilot adjusting screw down gradually; outlet pressure rises. Lock the screw when the required set point is reachedAdjust in small increments while watching the downstream gauge. Pressure can only be set upwards from a lower value - if set too high, repeat from step 1Standards and certificationFlange dimensionsISO 7005 / EN 1092-2Pressure testingEN 12266-1Quality managementISO 9001, certificate no. 05325Q30683R1SEnvironmental managementISO 14001, certificate no. 05325E30489R1SOccupational health and safetyISO 45001, certificate no. 05325S30455R1SISO 9001, ISO 14001 and ISO 45001 certificates are held by Hebei Hengya Technology Co., Ltd. and are valid until 19 October 2028.ApplicationsWater supply networks where a high-pressure main feeds a lower-pressure distribution zoneBuilding installations requiring a stable reduced pressureFire-fighting water supply systemsIndustrial water supply and process lines

Contact HENGYA for Shipping, delivery, and payments information.

Share to

Products Category

Tag list

Send Inquiry

*Note: Please fill in the information accurately and keep the communication open. We will contact you as soon as possible.

Submit

Related Products

Soft-sealed gate valves are divided into two types: rising stem soft-sealed gate valves and dark stem soft-sealed gate valves.
View Details View More
Soft-sealed gate valves are divided into two types: rising stem soft-sealed gate valves and dark stem soft-sealed gate valves.
View Details View More
Soft-sealed gate valves are divided into two types: rising stem soft-sealed gate valves and dark stem soft-sealed gate valves.
View Details View More
Soft-sealed gate valves are divided into two types: rising stem soft-sealed gate valves and dark stem soft-sealed gate valves.
View Details View More
< 1234...16 >

Request Quote

We will contact you within one working day. Please pay attention to your email.

SUBMIT