• Rubber Flap Check Valve, Flanged GGG50
  • Rubber Flap Check Valve, Flanged GGG50
  • Rubber Flap Check Valve, Flanged GGG50
  • Rubber Flap Check Valve, Flanged GGG50
  • Rubber Flap Check Valve, Flanged GGG50
  • Rubber Flap Check Valve, Flanged GGG50
Rubber Flap Check Valve, Flanged GGG50
Rubber Flap Check Valve, Flanged GGG50
Rubber Flap Check Valve, Flanged GGG50
Rubber Flap Check Valve, Flanged GGG50
Rubber Flap Check Valve, Flanged GGG50
Rubber Flap Check Valve, Flanged GGG50
+

Rubber Flap Check Valve, Flanged GGG50

Flanged rubber flap check valve with a bolted top cover for in-line service. Full bore body, low head loss, single moving part. DN40-DN800, PN10-PN25, GGG50.

Contact HENGYA for Shipping, delivery, and payments information.

Products Category

Tag list

  • 产品描述
  • What this valve does

    The HC44X is a flanged check valve that lets water run one way and stops it coming back. It sits in a supply main, a pump discharge line or a district branch, and there is nothing to operate: no handle, no actuator, no electrical supply. Forward flow lifts the rubber flap off its seat; when the flow stops or reverses, the flap drops back and the returning pressure seals it shut.

    Because the body is full bore and the only moving part is a single hinged flap, the valve adds very little resistance to the line and has almost nothing that can wear out of adjustment.

    Construction

    BodyDuctile iron GGG50 (QT450-10), epoxy coated inside and out
    Top coverDuctile iron GGG50, bolted, with a gasket joint to the body
    FlapRubber bonded to a steel insert plate, hinged on a through pin
    SeatRubber faced, at an angle to the bore
    Hinge pinStainless steel, retained in the body
    CoatingEpoxy resin, internal and external, for potable and waste water duty

    The size, pressure rating and body material are cast into the side of the body, so what is on the pipe can be checked against the drawing without opening anything.

    How the flap closes

    The flap hangs on a hinge pin above the seat. In forward flow it is pushed clear of the bore and sits almost parallel to the flow, which keeps head loss low. When the flow slows, the flap falls under its own weight; the moment the line pressure turns around, water on the downstream side presses the rubber face onto the seat and holds it there.

    The angled seat means the flap only has to travel a short distance before it lands, so the valve shuts before a full reverse flow can build up. That short travel is what keeps surge pressure down on pump discharge lines.

    Technical specification

    ModelHC44X
    Nominal sizeDN40 - DN800
    Nominal pressurePN10 / PN16 / PN25
    Body materialDuctile iron GGG50 (QT450-10)
    Flap materialEPDM as standard; NBR on request
    Working mediumWater, raw water, treated waste water
    Working temperature0 - 80 °C
    ConnectionFlanged, ISO 7005 / EN 1092-2
    DriveNone - flow operated
    Pressure testShell 1.5 x PN, seal 1.1 x PN to EN 12266-1

    Pressure ratings

    ParameterPN10PN16PN25
    Nominal pressure (MPa)1.01.62.5
    Shell test pressure (MPa)1.52.43.75
    Seal test pressure (MPa)1.11.762.75

    Flange and face-to-face

    Flange drilling meets EN 1092-2 for the pressure rating ordered. Face-to-face length and overall height for each size follow the drawing supplied with the quotation, so the valve can be set against the pipe schedule before it is made.

    Installation

    • Fits horizontal or vertical pipe; on vertical runs the flow must go upwards so the flap can fall closed
    • Follow the arrow cast on the body - it points in the permitted flow direction
    • Leave enough clearance above the top cover to lift it off for service
    • No pipeline stress may act on the body after bolting up; support the pipe either side on large sizes
    • Flush the line before commissioning so debris does not lodge under the flap
    • On pump discharge, fit the valve downstream of the pump and upstream of the isolating valve

    Maintenance

    Undo the cover bolts and lift the top cover off: the flap and hinge pin come out through the opening without cutting the valve out of the line. Inspect the rubber face for cuts or embedded grit, check that the flap swings freely, then refit with a new cover gasket. There is no spring to reset and no guide to align.

    Standards and certification

    Face-to-faceDIN 3202 F6
    Flange dimensionsISO 7005 / EN 1092-2
    Pressure testingEN 12266-1
    Quality managementISO 9001, certificate no. 05325Q30683R1S
    Environmental managementISO 14001, certificate no. 05325E30489R1S
    Occupational health and safetyISO 45001, certificate no. 05325S30455R1S

    ISO 9001, ISO 14001 and ISO 45001 certificates are held by Hebei Hengya Technology Co., Ltd. and are valid until 19 October 2028.

    Typical applications

    • Pump discharge on water supply and boosting stations, stopping back-flow when a pump stops
    • District metering and branch lines where return flow has to be blocked
    • Raw water intake and transfer mains
    • Treated waste water and drainage pumping mains
    • HVAC circulating systems where a chiller or boiler must not see reverse flow
    • Fire-fighting water supply, downstream of the main pump set

Rubber Flap Check Valve, Flanged GGG50

Flanged rubber flap check valve with a bolted top cover for in-line service. Full bore body, low head loss, single moving part. DN40-DN800, PN10-PN25, GGG50.

Contact HENGYA for Shipping, delivery, and payments information.

Share to

Products Category

Tag list

Send Inquiry

*Note: Please fill in the information accurately and keep the communication open. We will contact you as soon as possible.

Submit

Related Products

BS5163 non-rising stem soft seal gate valve, Z45X, ductile iron body with epoxy coating and EPDM seat. DN40-DN1200, PN10-PN25, flanged to EN 1092-2.
View Details View More
BS5163 rising stem soft seal gate valve, Z41X, stem position showing disc travel, ductile iron body. DN40-DN1200, PN10-PN25, flanged.
View Details View More
BS5163 Z45X heavy duty soft seal gate valve, thicker body wall for high pressure mains. DN40-DN1200, PN16-PN25, flanged, non-rising stem.
View Details View More
CFZ45X magnetic lock soft seal gate valve, key operated locking head against unauthorised use. DN40-DN300, PN10-PN16, flanged.
View Details View More
< 1234...16 >

Request Quote

We will contact you within one working day. Please pay attention to your email.

SUBMIT